Kenwood TH-D72E User Manual Page 73
- Page / 75
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SKY CMD – 3
PROGRAMMING CALL SIGNS
The built-in TNCs of the Commander and Transporter
communicate each other when you send a control
command from the Commander. So you must program
different call signs (9 digits max.) on these transceivers as
the IDs of the TNCs.
Use the following Menu Nos. to program call signs:
On Commander
500 COM Callsign Call sign for Commander
501 TRP Callsign Call sign for Transporter
On Transporter
500 COM Callsign Call sign for Commander
501 TRP Callsign Call sign for Transporter
1 Access Menu 500 or 501, then [ (OK)].
•The callsign entry field appears; the first digit blinks.
2 Press [ ]/[ ] or rotate the Tuning control to select a
character.
• You can enter 0 to 9, A to Z, and –.
3 Press [ OK].
• The cursor moves to the next digit.
4 Repeat steps 2 and 3 to enter up to 9 digits.
[ESC ]: Cancels entry of a call sign.
[A/B]: Deletes the digit at which the cursor is blinking.
5 Press [ OK]. to complete the setting.
6 Press [MENU] to exit Menu mode.
The keypad also is available to enter alphanumeric
characters in step 2.
PROGRAMMING A TONE FREQUENCY
On receiving a tone from the Commander, the Transporter
causes the HF transceiver to enter Transmit mode. On
both the Commander and Transporter, access Menu 502
and select the desired, same tone frequency.
CONTROL OPERATION
When in the Sky Command mode, the Microphone keys
of the Commander will function as below. First switch
ON the HF transceiver and press Microphone [0] on the
Commander.
Each time you press the desired key, the Commander
will automatically enter transmit mode and send the
corresponding control command to the Transporter.
Key Function
Tuning
control
Frequency or memory channel number
change
[1] (PWR) Power ON/ OFF
[2] (RX) HF frequency receive ON/ OFF
[3] (MODE) Modulation mode switch
[4] (RIT)
RIT ON/ OFF
[5] (XIT)
XIT ON/ OFF
[6] (CLR)
RIT offset or XIT offset clear
[7] (SPLIT)
Split-frequency ON/ OFF
[8] (M>V)
Transfer from Memory to VFO
[9] (A/B)
In VFO mode: VFO A/ VFO B switch
In Memory Recall mode: no change
[0] (SYNC)
Current settings retrieve (from HF
transceiver)
[MONI]
To monitor the UHF band on the
Commander
[B] (M/V)
VFO/ Memory Recall mode switch
[ ]
XIT/ RIT offset frequency increase
[ ]
XIT/ RIT offset frequency decrease
[ ]
1
(FAST)
In LSB, USB, or CW mode: 10 Hz/ 1 kHz
switch
In FM or AM mode: 1 kHz/ 10 kHz switch
[#]
2
(ENTER)
In VFO mode: frequency entry ON
In Memory Recall mode: channel number
entry ON
[PTT]
To transmit audio on an HF frequency
1
“FS” appears when you select 1 kHz step (LSB/ USB/ CW) or 10 kHz
step (FM/ AM).
2
After pressing [#], press [0] to [9] to enter a frequency or memory
channel number.
Tuning control
- INSTRUCTION MANUAL 1
- CONTENTS 2
- CONTENTS – 2 3
- CONTENTS – 3 4
- CONTENTS – 4 5
- CONTENTS – 5 6
- OPERATING THROUGH REPEATERS 7
- REPEATER – 2 8
- REPEATER – 3 9
- TRANSMITTING A 1750 Hz TONE 9
- REVERSE FUNCTION 9
- TONE FREQUENCY ID 9
- MEMORY CHANNELS 10
- MEMORY CH – 2 11
- RECALLING A MEMORY CHANNEL 11
- RECALLING A CALL CHANNEL 11
- CLEARING A MEMORY CHANNEL 11
- CHANNEL DISPLAY FUNCTION 12
- MEMORY CH – 3 12
- NAMING A MEMORY CHANNEL 12
- MEMORY-TO-VFO TRANSFER 12
- MEMORY CH – 4 13
- SCAN – 1 14
- SCAN – 2 15
- VFO SCAN 15
- MEMORY SCAN 15
- GROUP SCAN 15
- SCAN – 3 16
- SCAN – 4 17
- PROGRAM SCAN 17
- MHz SCAN 17
- CALL SCAN 17
- CTCSS/ DCS/ CROSS TONE 18
- CTCSS/ DCS/ CROSS TONE – 2 19
- CTCSS FREQUENCY SCAN 19
- USING DCS 19
- CROSS TONE 20
- MANUAL DIALING 21
- AUTOMATIC DIALER 21
- DTMF – 1 21
- DTMF – 2 22
- DTMF KEY LOCK 22
- EchoLink 23
- EchoLink – 2 24
- OTHER OPERATIONS 25
- OTHER OP – 2 26
- AUTO POWER OFF (APO) 26
- BATTERY TYPE 26
- KEY LOCK 26
- VOLUME BALANCE (BAND A/B) 26
- OTHER OP – 3 27
- KEY BEEP 27
- PROGRAMMABLE VFO 27
- PROGRAMMABLE FUNCTION KEYS 27
- OTHER OP – 4 28
- FREQUENCY DIRECT ENTRY 28
- SWITCHING FM/AM MODE 28
- BEAT SHIFT 28
- OTHER OP – 5 29
- TX INHIBIT 29
- SELECTING AN OUTPUT POWER 29
- OTHER OP – 6 30
- MASKING BANDS 30
- POWER ON PASSWORD 30
- What is GPS? 31
- GPS and APRS Position Format 31
- INTERNAL GPS FUNCTION ON/OFF 32
- INTERNAL GPS SETUP 32
- GPS DATA SETUP 33
- TRACK LOG 34
- LOG SETUP 35
- TARGET POINT 35
- MARK WAY POINT 36
- PACKET OPERATION 38
- PACKET – 2 39
- TNC COMMANDS LIST 39
- PACKET – 3 40
- PACKET – 4 41
- PACKET – 5 42
- PACKET – 6 43
- APRS – 1 44
- APRS – 2 45
- WEATHER STATION 45
- ADJUSTING THE INTERNAL CLOCK 45
- APRS – 3 46
- RECEIVING APRS DATA 46
- ACCESSING RECEIVED APRS DATA 46
- APRS – 4 47
- DISPLAY EXAMPLE 47
- APRS – 5 48
- SORT FUNCTION 48
- APRS – 6 49
- FILTER FUNCTION 49
- RECEIVING A MESSAGE 49
- APRS – 7 50
- ENTERING A MESSAGE 50
- APRS – 8 51
- TRANSMITTING A MESSAGE 51
- APRS – 9 52
- BASIC SETTINGS 52
- APRS – 10 53
- SETTING INTERNAL TNC 53
- SETTING COM PORT 53
- PROGRAMMING POSITION DATA 54
- APRS – 11 54
- SETTING WAY POINT 54
- PC PORT ON/OFF 54
- APRS – 12 55
- SETTING BEACON INFORMATION 55
- SELECTING A POSITION COMMENT 55
- APRS – 13 56
- STORING STATUS TEXT 56
- QSY FUNCTION 56
- APRS – 14 57
- SETTING PACKET FILTER 57
- APRS – 15 58
- SELECTING YOUR STATION ICON 58
- APRS – 16 59
- SETTING TX BEACON 59
- SETTING ALGORITHM 59
- APRS – 17 60
- SETTING SmartBeaconing 60
- APRS – 18 61
- PROGRAMMING A PACKET PATH 61
- APRS – 19 62
- APRS – 20 63
- VOICE ALERT 63
- WEATHER STATION DATA OUTPUT 63
- APRS – 21 64
- SETTING AS A DIGIPEATER 64
- APRS – 22 65
- STORING USER PHRASES 65
- STORING AUTO MESSAGE REPLY 65
- APRS – 23 66
- SETTING SOUND 66
- APRS – 24 67
- SETTING INTERRUPT DISPLAY 67
- APRS – 25 68
- SELECTING A DISPLAY UNIT 68
- SELECTING A NAVITRA GROUP 68
- STORING NAVITRA MESSAGE 68
- APRS – 26 69
- DX PACKETCLUSTERS MONITOR 69
- TRANSCEIVER RESET 70
- SKY COMMAND SYSTEM II 71
- SKY CMD – 2 72
- PREPARATION FLOW 72
- SKY CMD – 3 73
- PROGRAMMING CALL SIGNS 73
- PROGRAMMING A TONE FREQUENCY 73
- CONTROL OPERATION 73
- WEATHER ALERT (TH-D72A ONLY) 74
- PREPARATION 75
- WIRELESS OP – 1 75
Related products and manuals for GPS receiver Kenwood TH-D72E
GPS receiver Kenwood KCA-BT200 User Manual
(80 pages)
(80 pages)
GPS receiver Kenwood DNX9980HD User Manual
(92 pages)
(92 pages)
GPS receiver Kenwood KNA-G431 User Manual
(120 pages)
(120 pages)
GPS receiver Kenwood DNX710EX User Manual
(100 pages)
(100 pages)
GPS receiver Kenwood DDX8046BT User Manual
(124 pages)
(124 pages)
GPS receiver Kenwood DDX6046BT User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood KNA-G510 User Manual
(160 pages)
(160 pages)
GPS receiver Kenwood DNX7180 User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DNX7340BT User Manual
(20 pages)
(20 pages)
GPS receiver Kenwood DNX7100 User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DNX7240BT User Manual
(24 pages)
(24 pages)
GPS receiver Kenwood DNX6160 User Manual
(100 pages)
(100 pages)
GPS receiver Kenwood DNX7360BT User Manual
(12 pages)
(12 pages)
GPS receiver Kenwood DDX8024BT User Manual
(100 pages)
(100 pages)
GPS receiver Kenwood DNX7000EX User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DNX512EX User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DDX5036 User Manual
(11 pages)
(11 pages)
© 2020, manymanuals.com. All rights reserved. | 0.345 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals