Kenwood TH-D72E User Manual Page 53
- Page / 75
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
APRS – 10
SETTING INTERNAL TNC
Q Data Band
Access Menu 310.
On this transceiver you can select data band for APRS
mode independent of the selection for Packet mode.
Select band A or B as the data band for receiving or
transmitting APRS packets. The default is band A. “ ”
indicates the current data band.
Note: In Menu 310, the selection switches among A-Band,
B-Band, A:TX B:RX, and A:RX B:TX. Select A:TX B:RX or A:
RX B:TX if APRS networks which use two separate frequencies
become available in the future.
Q Packet Transfer Rate
Access Menu 311.
The default APRS packet transfer rate set on the built-
in TNC is 1200 bps which is the standard among the
current APRS networks.
Note: You can also set the Packet transfer rate to 9600bps when
necessary.
Q DCD Sense
Access Menu 320.
You can also select the method for inhibiting the built-in
TNC from transmitting.
D or RxD Band: When the data band is no longer
busy (as per the steps below), the packet is transmitted
after 1 second.
: Press [PTT] to enter transmit mode.
@ The data band is busy.
Both Band: When the bands are no longer busy (as
per the steps below), the packet is transmitted after 1
second.
: Press [PTT] to enter transmit mode.
@ The data band is busy.
. The other band is busy.
Ignore DCD: Transmission from the built-in TNC is
not inhibited. The packet is transmitted immediately.
Q TX delay time
Access Menu 321.
This function allows you to set a transmission delay
time between transmitting the APRS data and
transmitting a flag code prior to the APRS data. When
the other station has activated their Save Mode, set a
longer delay time.
SETTING COM PORT
Q Baud Rate
Access Menu 330.
Set the communication speed of the external GPS or
other equipment that is connected to the GPS terminal.
The speed is set to 4800 bps (NMEA)/ 9600 bps (IPS
format: SONY) when a GPS receiver is connected.
• It does not correspond to the Gamin-TXT format.
Q Input Type
Access Menu 331.
Off: You can perform APRS communications without
the use of a GPS receiver or Weather Station. Set
your station position data manually through Menu 360
(MY Position).
GPS: You can perform APRS communications using
a GPS receiver. Verify your station position data by
pressing the [POS] key.
Weather (Davis): You can perform APRS
communications using a Davis Weather Station. Verify
your station weather data by pressing the [WXI] (PF) key.
• Operation verification model (currently September 2010)
Vantage PRO2
TM
• Please use the Data Logger bundled with “WeatherLink
®
for Vantage Pro2
TM
, Windows, Serial Port” (Davis
Part No.06510SER) or “WeatherLink
®
for APRS, with
Streaming Data Logger” (Davis Part No.06540) with
Vantage PRO2
TM
.
• When using the “WeatherLink
®
for APRS, with Streaming
Data Logger” (Davis Part No.06540) Data Logger, set the
Baud Rate (Menu 330) to 9600bps for stable operation.
Weather (PeetBros. ): You can perform APRS
communications using a PeetBros Weather Station. Verify
your station weather data by pressing the [WXI] (PF) key.
• Operation verification model (currently September 2010)
ULTIMETER
®
2100 (Packet mode)
- INSTRUCTION MANUAL 1
- CONTENTS 2
- CONTENTS – 2 3
- CONTENTS – 3 4
- CONTENTS – 4 5
- CONTENTS – 5 6
- OPERATING THROUGH REPEATERS 7
- REPEATER – 2 8
- REPEATER – 3 9
- TRANSMITTING A 1750 Hz TONE 9
- REVERSE FUNCTION 9
- TONE FREQUENCY ID 9
- MEMORY CHANNELS 10
- MEMORY CH – 2 11
- RECALLING A MEMORY CHANNEL 11
- RECALLING A CALL CHANNEL 11
- CLEARING A MEMORY CHANNEL 11
- CHANNEL DISPLAY FUNCTION 12
- MEMORY CH – 3 12
- NAMING A MEMORY CHANNEL 12
- MEMORY-TO-VFO TRANSFER 12
- MEMORY CH – 4 13
- SCAN – 1 14
- SCAN – 2 15
- VFO SCAN 15
- MEMORY SCAN 15
- GROUP SCAN 15
- SCAN – 3 16
- SCAN – 4 17
- PROGRAM SCAN 17
- MHz SCAN 17
- CALL SCAN 17
- CTCSS/ DCS/ CROSS TONE 18
- CTCSS/ DCS/ CROSS TONE – 2 19
- CTCSS FREQUENCY SCAN 19
- USING DCS 19
- CROSS TONE 20
- MANUAL DIALING 21
- AUTOMATIC DIALER 21
- DTMF – 1 21
- DTMF – 2 22
- DTMF KEY LOCK 22
- EchoLink 23
- EchoLink – 2 24
- OTHER OPERATIONS 25
- OTHER OP – 2 26
- AUTO POWER OFF (APO) 26
- BATTERY TYPE 26
- KEY LOCK 26
- VOLUME BALANCE (BAND A/B) 26
- OTHER OP – 3 27
- KEY BEEP 27
- PROGRAMMABLE VFO 27
- PROGRAMMABLE FUNCTION KEYS 27
- OTHER OP – 4 28
- FREQUENCY DIRECT ENTRY 28
- SWITCHING FM/AM MODE 28
- BEAT SHIFT 28
- OTHER OP – 5 29
- TX INHIBIT 29
- SELECTING AN OUTPUT POWER 29
- OTHER OP – 6 30
- MASKING BANDS 30
- POWER ON PASSWORD 30
- What is GPS? 31
- GPS and APRS Position Format 31
- INTERNAL GPS FUNCTION ON/OFF 32
- INTERNAL GPS SETUP 32
- GPS DATA SETUP 33
- TRACK LOG 34
- LOG SETUP 35
- TARGET POINT 35
- MARK WAY POINT 36
- PACKET OPERATION 38
- PACKET – 2 39
- TNC COMMANDS LIST 39
- PACKET – 3 40
- PACKET – 4 41
- PACKET – 5 42
- PACKET – 6 43
- APRS – 1 44
- APRS – 2 45
- WEATHER STATION 45
- ADJUSTING THE INTERNAL CLOCK 45
- APRS – 3 46
- RECEIVING APRS DATA 46
- ACCESSING RECEIVED APRS DATA 46
- APRS – 4 47
- DISPLAY EXAMPLE 47
- APRS – 5 48
- SORT FUNCTION 48
- APRS – 6 49
- FILTER FUNCTION 49
- RECEIVING A MESSAGE 49
- APRS – 7 50
- ENTERING A MESSAGE 50
- APRS – 8 51
- TRANSMITTING A MESSAGE 51
- APRS – 9 52
- BASIC SETTINGS 52
- APRS – 10 53
- SETTING INTERNAL TNC 53
- SETTING COM PORT 53
- PROGRAMMING POSITION DATA 54
- APRS – 11 54
- SETTING WAY POINT 54
- PC PORT ON/OFF 54
- APRS – 12 55
- SETTING BEACON INFORMATION 55
- SELECTING A POSITION COMMENT 55
- APRS – 13 56
- STORING STATUS TEXT 56
- QSY FUNCTION 56
- APRS – 14 57
- SETTING PACKET FILTER 57
- APRS – 15 58
- SELECTING YOUR STATION ICON 58
- APRS – 16 59
- SETTING TX BEACON 59
- SETTING ALGORITHM 59
- APRS – 17 60
- SETTING SmartBeaconing 60
- APRS – 18 61
- PROGRAMMING A PACKET PATH 61
- APRS – 19 62
- APRS – 20 63
- VOICE ALERT 63
- WEATHER STATION DATA OUTPUT 63
- APRS – 21 64
- SETTING AS A DIGIPEATER 64
- APRS – 22 65
- STORING USER PHRASES 65
- STORING AUTO MESSAGE REPLY 65
- APRS – 23 66
- SETTING SOUND 66
- APRS – 24 67
- SETTING INTERRUPT DISPLAY 67
- APRS – 25 68
- SELECTING A DISPLAY UNIT 68
- SELECTING A NAVITRA GROUP 68
- STORING NAVITRA MESSAGE 68
- APRS – 26 69
- DX PACKETCLUSTERS MONITOR 69
- TRANSCEIVER RESET 70
- SKY COMMAND SYSTEM II 71
- SKY CMD – 2 72
- PREPARATION FLOW 72
- SKY CMD – 3 73
- PROGRAMMING CALL SIGNS 73
- PROGRAMMING A TONE FREQUENCY 73
- CONTROL OPERATION 73
- WEATHER ALERT (TH-D72A ONLY) 74
- PREPARATION 75
- WIRELESS OP – 1 75
Related products and manuals for GPS receiver Kenwood TH-D72E
GPS receiver Kenwood KCA-BT200 User Manual
(80 pages)
(80 pages)
GPS receiver Kenwood DNX9980HD User Manual
(92 pages)
(92 pages)
GPS receiver Kenwood KNA-G431 User Manual
(120 pages)
(120 pages)
GPS receiver Kenwood DNX710EX User Manual
(100 pages)
(100 pages)
GPS receiver Kenwood DDX8046BT User Manual
(124 pages)
(124 pages)
GPS receiver Kenwood DDX6046BT User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood KNA-G510 User Manual
(160 pages)
(160 pages)
GPS receiver Kenwood DNX7180 User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DNX7340BT User Manual
(20 pages)
(20 pages)
GPS receiver Kenwood DNX7100 User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DNX7240BT User Manual
(24 pages)
(24 pages)
GPS receiver Kenwood DNX6160 User Manual
(100 pages)
(100 pages)
GPS receiver Kenwood DNX7360BT User Manual
(12 pages)
(12 pages)
GPS receiver Kenwood DDX8024BT User Manual
(100 pages)
(100 pages)
GPS receiver Kenwood DNX7000EX User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DNX512EX User Manual
(32 pages)
(32 pages)
GPS receiver Kenwood DDX5036 User Manual
(11 pages)
(11 pages)
© 2020, manymanuals.com. All rights reserved. | 0.655 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals