Kenwood TM-D700A User Manual Page 54
- Page / 99
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
48
9
Note:
◆
If you start Visual Scan in Memory Recall mode, the memory
channel frequencies will be scanned.
◆
If you start Visual Scan after recalling the Call channel, the call
channel frequency will be used as the center frequency.
◆
If the frequency range specified for Program Scan or Program
VFO is narrower than the range specified for Visual Scan, the
range for Program Scan or VFO will be used for Visual Scan.
◆
Visual Scan stops while transmitting.
◆
Starting Visual Scan switches Automatic Band Change OFF.
◆
If you start Visual Scan in one of the following conditions, you
cannot receive in the current operating frequency. To use this
frequency, press [PAUSE] to halt Scan.
•
Memory Recall or Call Channel mode
•
A frequency in the 118, 220, or 1200 MHz band was selected
in VFO mode.
◆
Depending on conditions, Visual Scan and the conventional S-
meter may indicate different signal strength levels.
■ Using Visual Scan
1 Select the desired band.
2 Turn the Tuning control, or press Mic [UP]/
[DWN], to select the operating frequency.
• This frequency will also be used as the center
frequency.
3 Press [F], [VISUAL] to start Visual Scan.
• To halt Scan, press [PAUSE]. “PAUSE” appears and
blinks. Press [PAUSE] again to resume.
4 To change the operating frequency, turn the
Tuning control or press Mic [UP]/ [DWN].
• The displayed frequency changes and the cursor
moves.
• Press [SET] to use the changed operating frequency
as the center frequency.
• Press [RESET] to restore the previous operating
frequency.
5 To quit Visual Scan, press [ESC].
- INSTRUCTION MANUAL 1
- THANK YOU! 2
- MODELS COVERED BY THIS MANUAL 2
- FEATURES 2
- PRECAUTIONS 3
- NOTICES TO THE USER 3
- CONTENTS 4
- SUPPLIED ACCESSORIES 7
- PREPARATION 8
- Front Panel Installation 9
- FIXED STATION INSTALLATION 10
- MODULAR PLUG CABLE CONNECTION 10
- DC POWER CABLE CONNECTION 11
- Fixed Station Operation 12
- ANTENNA CONNECTION 13
- ACCESSORY CONNECTIONS 14
- YOUR FIRST QSO 15
- GETTING ACQUAINTED 16
- SQL control 17
- MAIN UNIT- FRONT 18
- MAIN UNIT- REAR 18
- MICROPHONE 19
- INDICATORS 20
- BASIC TRANSCEIVER MODES 21
- BUTTON FUNCTION DISPLAY 22
- BAND A & B 23
- TX BAND AND CONTROL BAND 23
- OPERATING BASICS 25
- ADJUSTING SQUELCH 26
- SELECTING A FREQUENCY 26
- TRANSMITTING 27
- MENU SET-UP 28
- MENU CONFIGURATION 29
- U.S.A./ Canada only 30
- RETAEPER 30
- TM-D700E: 1750 Hz Tone 31
- U.S.A./ Canada: Mile and °F 33
- EDIW,YALER 33
- FFO/retropsnarT/rednammoC 33
- OPERATING THROUGH REPEATERS 34
- PROGRAMMING OFFSET 35
- Activating Tone Function 36
- Selecting a Tone Frequency 36
- AUTOMATIC REPEATER OFFSET 37
- TRANSMITTING A 1750 Hz TONE 38
- AUTOMATIC SIMPLEX CHECK (ASC) 39
- REVERSE FUNCTION 39
- TONE FREQ. ID 40
- MEMORY CHANNELS 41
- REPEATER FREQUENCIES 42
- CLEARING A MEMORY CHANNEL 43
- RECALLING A MEMORY CHANNEL 43
- NAMING A MEMORY CHANNEL 44
- CALL CHANNEL 45
- MEMORY-TO-VFO TRANSFER 46
- CHANNEL DISPLAY 46
- PARTIAL OR FULL RESET? 47
- PROGRAMMABLE MEMORY (PM) 48
- APPLICATION EXAMPLES 49
- STORING IN PM CHANNELS 50
- RECALLING A PM CHANNEL 50
- AUTO PM CHANNEL STORE 51
- PM CHANNEL RESET 51
- 145.430 MHz 52
- VISUAL SCAN 53
- Using Visual Scan 54
- SELECTING SCAN RESUME METHOD 55
- MEMORY SCAN 56
- VFO SCAN 56
- GROUP SCAN 57
- PROGRAM SCAN 58
- MHz SCAN 59
- CALL/VFO SCAN 60
- CALL/MEMORY SCAN 60
- Not Received 61
- CTCSS FREQ. ID 62
- DIGITAL CODE SQUELCH (DCS) 63
- DCS CODE ID 64
- MANUAL DIALING 65
- AUTOMATIC DIALER 66
- Selecting TX Speed 67
- Selecting Pause Duration 67
- AUXILIARY FUNCTIONS 69
- CHANGING FREQUENCY STEP SIZE 70
- PROGRAMMABLE VFO 70
- DISPLAY DIMMER 71
- AUTO DIMMER CHANGE 71
- DISPLAY CONTRAST ADJUST 71
- POSITIVE/ NEGATIVE REVERSAL 71
- BLANKING A BAND DISPLAY 72
- TRANSCEIVER LOCK 73
- ALL-CONTROL LOCK 73
- S-METER SQUELCH 74
- CHANGING BEEP VOLUME 75
- KEY BEEP ON/ OFF 75
- SWITCHING FM/AM MODE 75
- TIME-OUT TIMER (TOT) 76
- AUTOMATIC POWER OFF (APO) 76
- POWER-ON MESSAGE 77
- DISPLAY DEMONSTRATION 77
- SPEAKER MUTE 78
- /ycneuqerF)SSCTCro(enoT 79
- DTMF tones 80
- CONTROL OPERATION 81
- SKY COMMAND 82
- 2 (U.S.A./ CANADA ONLY) 82
- TRANSCEIVER 83
- PREPARATION FLOW 84
- Repeater mode 88
- Cross-band 88
- Repeater 88
- OPTIONAL ACCESSORIES 90
- INSTALLING OPTIONS 91
- MAINTENANCE 93
- TROUBLESHOOTING 94
- SPECIFICATIONS 96
Related products and manuals for Car speakers Kenwood TM-D700A
Car speakers Kenwood KAC-7201 User Manual
(12 pages)
(12 pages)
Car speakers Kenwood DPX-5010 User Manual
(48 pages)
(48 pages)
Car speakers Kenwood KAC-929 User Manual
(2 pages)
(2 pages)
Car speakers Kenwood LZ-702W User Manual
(132 pages)
(132 pages)
Car speakers Kenwood X-SE9 User Manual
(56 pages)
(56 pages)
Car speakers Kenwood RC-D710 User Manual
(66 pages)
(66 pages)
Car speakers Kenwood KDC-2025 User Manual
(96 pages)
(96 pages)
Car speakers Kenwood KDC-136 User Manual
(20 pages)
(20 pages)
Car speakers Kenwood XXV-01D User Manual
(104 pages)
(104 pages)
Car speakers Kenwood DPX404U User Manual
(79 pages)
(79 pages)
Car speakers Kenwood LZ-702W User Manual
(17 pages)
(17 pages)
© 2020, manymanuals.com. All rights reserved. | 2.552 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals