Kenwood TM-D700A User Manual Page 11
- Page / 99
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
5
1
2 After the cable is in place, wind heat-resistant tape
around the fuse holder to protect it from moisture.
Tie down the full run of cable.
3 To prevent the risk of short circuits, disconnect
other wiring from the negative (–) battery terminal
before connecting the transceiver.
4 Confirm the correct polarity of the connections,
and attach the power cable to the battery
terminals; red connects to the positive (+)
terminal, black connects to the negative (–)
terminal.
• Use the full length of the cable without cutting off
excess even if the cable is longer than required. In
particular, never remove the fuse holders from the
cable.
5 Reconnect any wiring removed from the negative
terminal.
6 Connect the DC power cable to the transceiver’s
power supply connector.
• Press the connectors firmly together until the locking
tab clicks.
DC POWER CABLE CONNECTION
■ Mobile Operation
The vehicle battery must have a nominal rating of 12 V.
Never connect the transceiver to a 24 V battery. Be
sure to use a 12 V vehicle battery that has sufficient
current capacity. If the current to the transceiver is
insufficient, the display may darken during transmission,
or transmit output power may drop excessively.
1 Route the DC power cable supplied with the
transceiver directly to the vehicle’s battery
terminals using the shortest path from the
transceiver.
• If using a noise filter, it should be installed with an
insulator to prevent it from touching metal on the
vehicle.
• It is recommended not to use the cigarette lighter
socket since some cigarette lighter sockets introduce
an unacceptable voltage drop.
• If the power cable must be routed through a hole in
the vehicle chassis or body, for example in the
firewall at the front of the passenger compartment,
use a rubber grommet to protect the cable from
abrasion. Dismantle the fuse holder to pass the
cable through the firewall.
• The entire length of the cable must be dressed so it
is isolated from heat, moisture, and the engine
secondary (high voltage) ignition system/ cables.
Red
Black
Fuse holder
Fuse holder
- INSTRUCTION MANUAL 1
- THANK YOU! 2
- MODELS COVERED BY THIS MANUAL 2
- FEATURES 2
- PRECAUTIONS 3
- NOTICES TO THE USER 3
- CONTENTS 4
- SUPPLIED ACCESSORIES 7
- PREPARATION 8
- Front Panel Installation 9
- FIXED STATION INSTALLATION 10
- MODULAR PLUG CABLE CONNECTION 10
- DC POWER CABLE CONNECTION 11
- Fixed Station Operation 12
- ANTENNA CONNECTION 13
- ACCESSORY CONNECTIONS 14
- YOUR FIRST QSO 15
- GETTING ACQUAINTED 16
- SQL control 17
- MAIN UNIT- FRONT 18
- MAIN UNIT- REAR 18
- MICROPHONE 19
- INDICATORS 20
- BASIC TRANSCEIVER MODES 21
- BUTTON FUNCTION DISPLAY 22
- BAND A & B 23
- TX BAND AND CONTROL BAND 23
- OPERATING BASICS 25
- ADJUSTING SQUELCH 26
- SELECTING A FREQUENCY 26
- TRANSMITTING 27
- MENU SET-UP 28
- MENU CONFIGURATION 29
- U.S.A./ Canada only 30
- RETAEPER 30
- TM-D700E: 1750 Hz Tone 31
- U.S.A./ Canada: Mile and °F 33
- EDIW,YALER 33
- FFO/retropsnarT/rednammoC 33
- OPERATING THROUGH REPEATERS 34
- PROGRAMMING OFFSET 35
- Activating Tone Function 36
- Selecting a Tone Frequency 36
- AUTOMATIC REPEATER OFFSET 37
- TRANSMITTING A 1750 Hz TONE 38
- AUTOMATIC SIMPLEX CHECK (ASC) 39
- REVERSE FUNCTION 39
- TONE FREQ. ID 40
- MEMORY CHANNELS 41
- REPEATER FREQUENCIES 42
- CLEARING A MEMORY CHANNEL 43
- RECALLING A MEMORY CHANNEL 43
- NAMING A MEMORY CHANNEL 44
- CALL CHANNEL 45
- MEMORY-TO-VFO TRANSFER 46
- CHANNEL DISPLAY 46
- PARTIAL OR FULL RESET? 47
- PROGRAMMABLE MEMORY (PM) 48
- APPLICATION EXAMPLES 49
- STORING IN PM CHANNELS 50
- RECALLING A PM CHANNEL 50
- AUTO PM CHANNEL STORE 51
- PM CHANNEL RESET 51
- 145.430 MHz 52
- VISUAL SCAN 53
- Using Visual Scan 54
- SELECTING SCAN RESUME METHOD 55
- MEMORY SCAN 56
- VFO SCAN 56
- GROUP SCAN 57
- PROGRAM SCAN 58
- MHz SCAN 59
- CALL/VFO SCAN 60
- CALL/MEMORY SCAN 60
- Not Received 61
- CTCSS FREQ. ID 62
- DIGITAL CODE SQUELCH (DCS) 63
- DCS CODE ID 64
- MANUAL DIALING 65
- AUTOMATIC DIALER 66
- Selecting TX Speed 67
- Selecting Pause Duration 67
- AUXILIARY FUNCTIONS 69
- CHANGING FREQUENCY STEP SIZE 70
- PROGRAMMABLE VFO 70
- DISPLAY DIMMER 71
- AUTO DIMMER CHANGE 71
- DISPLAY CONTRAST ADJUST 71
- POSITIVE/ NEGATIVE REVERSAL 71
- BLANKING A BAND DISPLAY 72
- TRANSCEIVER LOCK 73
- ALL-CONTROL LOCK 73
- S-METER SQUELCH 74
- CHANGING BEEP VOLUME 75
- KEY BEEP ON/ OFF 75
- SWITCHING FM/AM MODE 75
- TIME-OUT TIMER (TOT) 76
- AUTOMATIC POWER OFF (APO) 76
- POWER-ON MESSAGE 77
- DISPLAY DEMONSTRATION 77
- SPEAKER MUTE 78
- /ycneuqerF)SSCTCro(enoT 79
- DTMF tones 80
- CONTROL OPERATION 81
- SKY COMMAND 82
- 2 (U.S.A./ CANADA ONLY) 82
- TRANSCEIVER 83
- PREPARATION FLOW 84
- Repeater mode 88
- Cross-band 88
- Repeater 88
- OPTIONAL ACCESSORIES 90
- INSTALLING OPTIONS 91
- MAINTENANCE 93
- TROUBLESHOOTING 94
- SPECIFICATIONS 96
Related products and manuals for Car speakers Kenwood TM-D700A
Car speakers Kenwood KAC-7201 User Manual
(12 pages)
(12 pages)
Car speakers Kenwood DPX-5010 User Manual
(48 pages)
(48 pages)
Car speakers Kenwood KAC-929 User Manual
(2 pages)
(2 pages)
Car speakers Kenwood LZ-702W User Manual
(132 pages)
(132 pages)
Car speakers Kenwood X-SE9 User Manual
(56 pages)
(56 pages)
Car speakers Kenwood RC-D710 User Manual
(66 pages)
(66 pages)
Car speakers Kenwood KDC-2025 User Manual
(96 pages)
(96 pages)
Car speakers Kenwood KDC-136 User Manual
(20 pages)
(20 pages)
Car speakers Kenwood XXV-01D User Manual
(104 pages)
(104 pages)
Car speakers Kenwood DPX404U User Manual
(79 pages)
(79 pages)
Car speakers Kenwood LZ-702W User Manual
(17 pages)
(17 pages)
© 2020, manymanuals.com. All rights reserved. | 1.703 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals