Kenwood TM-D700A User Manual Page 13
- Page / 99
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
7
1
■ Replacing Fuses
If the fuse blows, determine the cause, then correct
the problem. After the problem is resolved, replace
the fuse. If newly installed fuses continue to blow,
disconnect the power cable and contact your
authorized KENWOOD dealer or an authorized
KENWOOD service center for assistance.
Only use fuses of the specified type and rating; otherwise the
transceiver could be damaged.
Note: If you use the transceiver for a long period when the vehicle
battery is not fully charged, or when the engine is OFF, the battery
may become discharged, and will not have sufficient reserves to start
the vehicle. Avoid using the transceiver under these conditions.
ANTENNA CONNECTION
Before operating, you must first install an efficient,
well-tuned antenna. The success of your installation will
depend largely on the type of antenna and its correct
installation. The transceiver can give excellent results if
the antenna system and its installation are given careful
attention.
You should choose a 50 Ω impedance antenna to match
the transceiver input impedance. Use low-loss coaxial
feed line that also has a characteristic impedance of
50 Ω . Coupling the antenna to the transceiver via feed
lines having an impedance other than 50 Ω reduces the
efficiency of the antenna system, and can cause
interference to nearby broadcast television receivers,
radio receivers, and other electronic equipment.
◆
Transmitting without first connecting an antenna or other
matched load may damage the transceiver. Always connect the
antenna to the transceiver before transmitting.
◆
All fixed stations should be equipped with a lightning arrester to
reduce the risk of fire, electric shock, and transceiver damage.
noitacoLesuF gnitaRtnerruCesuF
reviecsnarTA51
yrosseccAdeilppuS
elbaCrewoPCD
A02
Feed line connector
Antenna
connector
To antenna
- INSTRUCTION MANUAL 1
- THANK YOU! 2
- MODELS COVERED BY THIS MANUAL 2
- FEATURES 2
- PRECAUTIONS 3
- NOTICES TO THE USER 3
- CONTENTS 4
- SUPPLIED ACCESSORIES 7
- PREPARATION 8
- Front Panel Installation 9
- FIXED STATION INSTALLATION 10
- MODULAR PLUG CABLE CONNECTION 10
- DC POWER CABLE CONNECTION 11
- Fixed Station Operation 12
- ANTENNA CONNECTION 13
- ACCESSORY CONNECTIONS 14
- YOUR FIRST QSO 15
- GETTING ACQUAINTED 16
- SQL control 17
- MAIN UNIT- FRONT 18
- MAIN UNIT- REAR 18
- MICROPHONE 19
- INDICATORS 20
- BASIC TRANSCEIVER MODES 21
- BUTTON FUNCTION DISPLAY 22
- BAND A & B 23
- TX BAND AND CONTROL BAND 23
- OPERATING BASICS 25
- ADJUSTING SQUELCH 26
- SELECTING A FREQUENCY 26
- TRANSMITTING 27
- MENU SET-UP 28
- MENU CONFIGURATION 29
- U.S.A./ Canada only 30
- RETAEPER 30
- TM-D700E: 1750 Hz Tone 31
- U.S.A./ Canada: Mile and °F 33
- EDIW,YALER 33
- FFO/retropsnarT/rednammoC 33
- OPERATING THROUGH REPEATERS 34
- PROGRAMMING OFFSET 35
- Activating Tone Function 36
- Selecting a Tone Frequency 36
- AUTOMATIC REPEATER OFFSET 37
- TRANSMITTING A 1750 Hz TONE 38
- AUTOMATIC SIMPLEX CHECK (ASC) 39
- REVERSE FUNCTION 39
- TONE FREQ. ID 40
- MEMORY CHANNELS 41
- REPEATER FREQUENCIES 42
- CLEARING A MEMORY CHANNEL 43
- RECALLING A MEMORY CHANNEL 43
- NAMING A MEMORY CHANNEL 44
- CALL CHANNEL 45
- MEMORY-TO-VFO TRANSFER 46
- CHANNEL DISPLAY 46
- PARTIAL OR FULL RESET? 47
- PROGRAMMABLE MEMORY (PM) 48
- APPLICATION EXAMPLES 49
- STORING IN PM CHANNELS 50
- RECALLING A PM CHANNEL 50
- AUTO PM CHANNEL STORE 51
- PM CHANNEL RESET 51
- 145.430 MHz 52
- VISUAL SCAN 53
- Using Visual Scan 54
- SELECTING SCAN RESUME METHOD 55
- MEMORY SCAN 56
- VFO SCAN 56
- GROUP SCAN 57
- PROGRAM SCAN 58
- MHz SCAN 59
- CALL/VFO SCAN 60
- CALL/MEMORY SCAN 60
- Not Received 61
- CTCSS FREQ. ID 62
- DIGITAL CODE SQUELCH (DCS) 63
- DCS CODE ID 64
- MANUAL DIALING 65
- AUTOMATIC DIALER 66
- Selecting TX Speed 67
- Selecting Pause Duration 67
- AUXILIARY FUNCTIONS 69
- CHANGING FREQUENCY STEP SIZE 70
- PROGRAMMABLE VFO 70
- DISPLAY DIMMER 71
- AUTO DIMMER CHANGE 71
- DISPLAY CONTRAST ADJUST 71
- POSITIVE/ NEGATIVE REVERSAL 71
- BLANKING A BAND DISPLAY 72
- TRANSCEIVER LOCK 73
- ALL-CONTROL LOCK 73
- S-METER SQUELCH 74
- CHANGING BEEP VOLUME 75
- KEY BEEP ON/ OFF 75
- SWITCHING FM/AM MODE 75
- TIME-OUT TIMER (TOT) 76
- AUTOMATIC POWER OFF (APO) 76
- POWER-ON MESSAGE 77
- DISPLAY DEMONSTRATION 77
- SPEAKER MUTE 78
- /ycneuqerF)SSCTCro(enoT 79
- DTMF tones 80
- CONTROL OPERATION 81
- SKY COMMAND 82
- 2 (U.S.A./ CANADA ONLY) 82
- TRANSCEIVER 83
- PREPARATION FLOW 84
- Repeater mode 88
- Cross-band 88
- Repeater 88
- OPTIONAL ACCESSORIES 90
- INSTALLING OPTIONS 91
- MAINTENANCE 93
- TROUBLESHOOTING 94
- SPECIFICATIONS 96
Related products and manuals for Car speakers Kenwood TM-D700A
Car speakers Kenwood KAC-7201 User Manual
(12 pages)
(12 pages)
Car speakers Kenwood DPX-5010 User Manual
(48 pages)
(48 pages)
Car speakers Kenwood KAC-929 User Manual
(2 pages)
(2 pages)
Car speakers Kenwood LZ-702W User Manual
(132 pages)
(132 pages)
Car speakers Kenwood X-SE9 User Manual
(56 pages)
(56 pages)
Car speakers Kenwood RC-D710 User Manual
(66 pages)
(66 pages)
Car speakers Kenwood KDC-2025 User Manual
(96 pages)
(96 pages)
Car speakers Kenwood KDC-136 User Manual
(20 pages)
(20 pages)
Car speakers Kenwood XXV-01D User Manual
(104 pages)
(104 pages)
Car speakers Kenwood DPX404U User Manual
(79 pages)
(79 pages)
Car speakers Kenwood LZ-702W User Manual
(17 pages)
(17 pages)
AEG AGE62516NX manuals
Owner’s manuals and user’s guides for Freezers AEG AGE62516NX.
We providing 6 pdf manuals AEG AGE62516NX for download free by document types: User Manual
Comments to this Manuals