Kenwood TS-480SAT User Manual Page 85

  • Download
  • Add to my manuals
  • Print
  • Page
    / 104
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 84
77
14 CONNECTING PERIPHERAL EQUIPMENT
RTTY OPERATION
Use the REMOTE and DATA connectors to interface with your MCP. If your MCP supports RTTY keying output,
connect the output to pin 8 of the REMOTE connector. Connect the demodulation input line of the MCP to
pin 5 of the DATA connector {page 78}. Also, connect the transmission control line of the MCP to pin 3 of the
REMOTE terminal. Select “FSK” or ”FSR” when you operate the RTTY mode.
Note:
Do not share a single power supply between the transceiver and the RTTY equipment. Keep as wide a separation as possible between the
transceiver and the RTTY equipment to reduce noise-pickup by the transceiver.
PADELE
KEY
EXT.SP
DATA
REMOTE
COM
MIC
PANE L
MCP
MCP
Power supply
Power supply
for the TS-480
Mini-DIN (6-pin)
Mini-DIN (8-pin)
HF/ 50 MHz LINEAR AMPLIFIER
Connect an external transmission power amplifier to the REMOTE connector (1 male, 8-pin mini DIN connector
(E57-0405-XX) is supplied). Switch ON the linear amplifier control relay via Menu Nos. 28 (HF) and 29 (50 MHz).
Select “2” or “3” if you use the internal relay to control the linear amplifier status.
The TX/ RX relay response time is 10 ms when you have selected CW Full Break-in and 25 ms when you have
selected CW Semi Break-in.
Note:
The TX/ RX control method differs, depending on external amplifier models. Some amplifiers enter the TX mode when the control terminal is
grounded. For those amplifiers, connect pin 2 of the
REMOTE
connector to the GND terminal of the amplifier and connect pin 4 of the
connector to the control terminal of the amplifier.
The mini DIN connectors (
DATA
and
REMOTE
connectors) look alike. Confirm the number of pins before plugging into the transceiver
connectors. The
REMOTE
connector is an 8-pin mini DIN connector and the
DATA
connector is a 6-pin mini DIN connector.
PADELE KEY
E
X
T
.S
P
D
A
T
A
R
E
M
O
T
E
C
O
M
MIC
PANEL
To antenna
Linear Amp.
Use the supplied
mini DIN (8-pin) connector to
interface with the Linear Amp.
TS-480HX/ SAT
yi
u
r
REMOTE connector
(Front view)
GND
q
et
w
r
w
t
Internal relay
for the Linear amplifier.
.oNniP
niP
emaN
noitcnuF
1OPStuptuorekaepS
2MOCyalerehtfolanimretnommoC
3SS
.timsnartotlanimretsihtdnuorG
(INA ATAD lanimret)rotcennoc
.FFOsnrut
4EKM
nehw)2nip(MOCotstcennoC
.stimsnartreviecsnarteht
5KRB
nehw)2nip(MOCotstcennoC
.seviecerreviecsnarteht
6CLA)V7(reifilpmamorftupniCLA
7LR
nehwtuptuosiCDV21+.xorppA
stimsnartreviecsnarteht
.).xamAm01(
8KTR
.tupnigniyek)KSF(YTTR
etanretlaotlanimretsihtdnuorG
.ecapSdnakraM
lateM
revoc
–dnuorG
REMOTE terminal pin assignment (8-pin mini DIN)
Page view 84
1 2 ... 80 81 82 83 84 85 86 87 88 89 90 ... 103 104

Comments to this Manuals

No comments