Kenwood TS-480SAT User Manual Page 46
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
38
8 COMMUNICATING AIDS
CUSTOMIZING TRANSMISSION SIGNAL
CHARACTERISTICS
The quality of your transmission signal is important,
regardless of which on-air activity you pursue.
However, it is easy to be casual and overlook this fact
since you don’t listen to your own signal.
The following sub-sections provide information that
will help you tailor your transmission signal.
■
TX Filter Bandwidth (SSB/ AM)
Use Menu No. 20 to select one of the following TX
filter bandwidths: 2.0 kHz or 2.4 kHz (default).
yalpsiD htdiwdnaB ycneuqerfdnabssaP
0.2zHk0.2zH0052~005
4.2zHk4.2zH0072~003
■ TX Equalizer (SSB/ FM/ AM)
Use Menu No. 19 to change the transmission
frequency characteristics of your signal. You can
select from one of 6 different transmission profiles
including the default flat response. Selecting any of
the following items from the Menu causes “EQ
ss
ss
s
T”
to appear on the display.
• Off (oFF):
The flat frequency response for SSB, FM, and
AM (default).
• High boost 1 (Hb1)/ High boost 2 (Hb2):
Emphasizes higher audio frequencies; effective
for a bassy voice. High boost 2 does not
reduce the low frequency as much as High
boost 1.
• Formant pass (FP):
Improves clarity by suppressing audio
frequencies outside the normal voice frequency
range.
• Bass boost 1 (bb1)/ Bass boost 2 (bb2):
Emphasizes lower audio frequencies; effective
for a voice with more high frequency
components. Bass boost 2 emphasises more
low frequency response.
• Conventional (c):
Emphasizes by 3 dB frequencies at 600 Hz
and higher.
• User (U):
Reserved for the optional ARCP software.
Off (oFF) is programmed at the factory as a
default.
Frequency Response Curves
TRANSMIT INHIBIT
Transmit Inhibit prevents the transceiver from being
placed in transmission mode. No signal can be
transmitted when this function is ON even if Mic [PTT]
is pressed.
• TX Inhibit OFF: Transmission is allowed.
• TX Inhibit ON: Transmission is not allowed.
Switch the function ON or OFF via Menu No. 55.
The default is OFF.
BUSY LOCKOUT
Busy Lockout prevents the transceiver from being
placed in transmit mode. Transmission is not allowed
if the current operating frequency is busy (in other
words, the squelch is open).
• Busy Lockout OFF: Transmission is allowed.
• Busy Lockout ON: Transmission is not allowed.
Switch the function ON or OFF via Menu No. 58.
The default is OFF.
CHANGING FREQUENCY WHILE TRANSMITTING
Moving your frequency while transmitting is usually
an unwise practice due to the risk of interfering with
other stations. However, if necessary, by using the
Tuning control you can change the operating
frequency while transmitting. You also can change
the XIT offset frequency while in transmission mode.
While transmitting, if you select a frequency outside
the transmission frequency range, the transceiver is
automatically forced to return to the reception mode.
If you selected transmission mode by pressing Mic
[PTT], transmission will not resume until you select a
frequency inside the transmission frequency range, at
which time you must release and press Mic [PTT]
again.
0.7
2.2
Amplitude
Audio
frequency
(kHz)
Bass boost (bb1, bb2)
High boost (Hb1, Hb2)
Off (oFF)
Conventional (c)
Formant pass (FP)
- TS-480HX 1
- TS-480SAT 1
- FCC WARNING 2
- BY THE FCC 2
- THANK YOU 3
- PRECAUTIONS 5
- CONTENTS 6
- INSTALLATION 9
- 1 INSTALLATION 10
- ANTENNA CONNECTION 10
- GROUND CONNECTION 10
- IGNITION NOISE 10
- DC POWER CABLE CONNECTION 10
- )renutannetnalanretxenaroF( 13
- TX/ RX UNIT 15
- REMOTE CONTROL PANEL 15
- YOUR FIRST QSO 16
- 2 YOUR FIRST QSO 17
- TRANSMISSION 17
- GETTING ACQUAINTED 18
- 3 GETTING ACQUAINTED 19
- LCD DISPLAY 21
- REMOTE CONTROL PANEL (REAR) 25
- MICROPHONE 25
- OPERATING BASICS 26
- 4 OPERATING BASICS 27
- SELECTING A BAND 27
- SELECTING A MODE 27
- ADJUSTING SQUELCH 27
- SELECTING A FREQUENCY 27
- SELECTING TRANSMISSION POWER 28
- MICROPHONE GAIN 29
- MENU SETUP 30
- 5 MENU SETUP 31
- MENU CONFIGURATION 31
- )1ECIOV( 33
- )INOMXR( 33
- ALPHABETICAL FUNCTION LIST 34
- BASIC COMMUNICATIONS 35
- 6 BASIC COMMUNICATIONS 36
- AUTO ZERO-BEAT 37
- ENHANCED COMMUNICATIONS 38
- 7 ENHANCED COMMUNICATIONS 39
- TRANSMITTING A TONE 40
- TONE FREQ. ID SCAN 40
- CTCSS FREQ. ID SCAN 41
- COMMUNICATING AIDS 42
- 8 COMMUNICATING AIDS 43
- AGC (AUTOMATIC GAIN CONTROL) 43
- VOX (VOICE-OPERATED TRANSMIT) 44
- SPEECH PROCESSOR 45
- TX Filter Bandwidth (SSB/ AM) 46
- TX Equalizer (SSB/ FM/ AM) 46
- Frequency Response Curves 46
- CHANGING KEYING SPEED 47
- AUTO WEIGHTING 47
- BUG KEY FUNCTION 48
- CW MESSAGE MEMORY 48
- FREQUENCY CORRECTION FOR CW 49
- AUTO CW TX IN SSB MODE 49
- MIC UP/ DWN KEY PADDLE MODE 49
- SPECIALIZED COMMUNICATIONS 50
- 9 SPECIALIZED COMMUNICATIONS 51
- SLOW SCAN TV/ FACSIMILE 52
- REJECTING INTERFERENCE 53
- 10 REJECTING INTERFERENCE 54
- BEAT CANCEL (SSB/ FM/ AM) 55
- NOISE REDUCTION (ALL MODES) 55
- PRE-AMPLIFIER 57
- ATTENUATOR 57
- CW REVERSE (RECEPTION) 57
- MEMORY FEATURES 58
- 11 MEMORY FEATURES 59
- MEMORY RECALL AND SCROLL 59
- MEMORY TRANSFER 60
- STORING FREQUENCY RANGES 61
- MEMORY CHANNEL LOCKOUT 62
- ERASING MEMORY CHANNELS 62
- MEMORY CHANNEL NAME 62
- STORING INTO QUICK MEMORY 63
- TEMPORARY FREQUENCY CHANGES 63
- QUICK MEMORY ➡ VFO TRANSFER 63
- VFO SCAN 64
- PROGRAM SCAN 64
- 12 SCAN 65
- PROGRAM SCAN PARTIALLY SLOWED 65
- SCAN HOLD 65
- SCAN RESUME METHOD 66
- ALL-CHANNEL SCAN 66
- GROUP SCAN 67
- OPERATOR CONVENIENCES 68
- 13 OPERATOR CONVENIENCES 69
- BEEP FUNCTION 70
- BRIGHTNESS 71
- KEY ILLUMINATION 71
- FREQUENCY LOCK FUNCTION 71
- TUNING CONTROL LOCK FUNCTION 71
- EQUALIZING RECEIVING AUDIO 72
- SETTING UP 74
- USING QUICK TRANSFER 74
- COMMUNICATION PARAMETERS 75
- RECORDING MESSAGES 76
- MESSAGE PLAYBACK 77
- CONSTANT RECORDING 77
- VOICE GUIDE 78
- CROSSBAND REPTEATER 79
- DX PACKETCLUSTER TUNE 80
- SKY COMMAND II (K-TYPE ONLY) 81
- SKY COMMAND II DIAGRAM 81
- PREPARATION 81
- CONTROL OPERATION 81
- USING TH-D7A AS A COMMANDER 82
- To COM port 84
- Straight-wired 84
- Linear Amp 85
- Use the supplied 85
- TS-480HX/ SAT 85
- MCP/ TNC 86
- DATA connector 86
- (Front view) 86
- ANT 1 connector 86
- TS-480 transceiver 87
- TM-D700 transceiver 87
- Cross-wired cable 87
- INSTALLING OPTIONS 89
- 15 INSTALLING OPTIONS 90
- TROUBLESHOOTING 91
- 16 TROUBLESHOOTING 92
- INITIAL SETTINGS 96
- PARTIAL RESET 96
- FULL RESET 96
- OPTIONAL ACCESSORIES 98
- SPECIFICATIONS 99
- 20 SPECIFICATIONS 100
- 19 INDEX 102
Related products and manuals for Boating Accessories Kenwood TS-480SAT
(66 pages)
(8 pages)
(8 pages)
Boating Accessories Kenwood TS-480HX User Manual
(104 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 0.970 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals