Kenwood TM-D710GA User Manual Page 20
- Page / 77
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SCAN-4
VISUAL SCAN
While you are receiving, Visual Scan allows you to monitor
frequencies near the current operating frequency. Visual Scan
graphically and simultaneously shows how all frequencies in the
selected range are busy. You will see up to 21 segments, for each
channel, that represent 7 S-meter levels (3 segments per level).
Determine the scan range by selecting the center frequency and
the number of channels. The default number of channels is 61.
Cursor
S-meter level
■ Selecting the Number of Channels
1 Enter Menu mode and access Menu 916.
2 Set the number of channels to MODE 1 (31ch), MODE 2
(61ch), MODE 3 (91ch), or MODE 4 (181ch).
■ Using Visual Scan
1 Select your desired band.
2 Rotate the Tuning control select the operating frequency.
• This frequency will be used as the center frequency.
3 Press [F], [VISUAL] to start Visual Scan.
• To halt Scan, press [PAUSE]. “PAUSE” appears and blinks.
Press [PAUSE] again to resume.
4 To change the operating frequency, rotate the Tuning
control.
• The displayed frequency changes and the cursor moves.
• Press [SET] to use the changed operating frequency as the
center frequency.
• Press [RESET] to restore the previous operating frequency.
5 To exit Visual Scan, press [ESC].
Note:
◆ You cannot use the Visual Scan Function under the following
circumstances:
• When the APRS/NAVITRA or Packet mode is turned
ON.
• When only 1 channel has been stored in the memory
channels.
• When using Weather Alert (K models only).
◆ If you start Visual Scan in Memory Recall mode, the memory channel
frequencies will be scanned.
◆ If you start Visual Scan after recalling the Call channel, the Call
channel frequency will be used as the center frequency.
◆ If the frequency range specifi ed for Program Scan or Program VFO
is narrower than the range specifi ed for Visual Scan, the range for
Program Scan or VFO will be used for Visual Scan.
◆ Visual Scan stops while transmitting.
◆ If you start Visual Scan in one of the following conditions, you cannot
receive in the current operating frequency. To use this frequency, press
[PAUSE] to halt Scan.
• Memory Recall or Call Channel mode.
• A frequency in the 118, 220, 300, or 1200 MHz band was selected
in VFO mode.
◆ Depending on the transceiver conditions, Visual Scan and the
conventional S-meter may indicate different signal strength levels.
- TM-D710GA 1
- TM-D710GE 1
- CONTENTS 2
- CONTENTS-2 3
- CONTENTS-3 4
- CONTENTS-4 5
- CONTENTS-5 6
- CONTENTS-6 7
- OPERATING THROUGH REPEATERS 8
- REPEATER-2 9
- REPEATER-3 10
- TRANSMITTING A 1750 Hz TONE 10
- REVERSE FUNCTION 10
- TONE FREQUENCY ID 10
- MEMORY CHANNELS 11
- CLEARING A MEMORY CHANNEL 12
- MEMORY CH-2 12
- RECALLING A MEMORY CHANNEL 12
- MEMORY CH-3 13
- NAMING A MEMORY CHANNEL 13
- MEMORY-TO-VFO TRANSFER 13
- CHANNEL DISPLAY FUNCTION 13
- MEMORY CH-4 14
- PROGRAMMABLE MEMORY (PM) 15
- PM CHANNEL RESET 16
- STORING DATA IN PM CHANNELS 16
- RECALLING PM CHANNELS 16
- AUTO PM CHANNEL STORE 16
- ■ Time-Operate Resume Time 17
- VFO SCAN 18
- MEMORY SCAN 18
- GROUP SCAN 18
- PROGRAM SCAN 19
- MHz SCAN 19
- CALL SCAN 19
- VISUAL SCAN 20
- CTCSS/ DCS/ CROSS TONE 21
- SIGNALING-2 22
- CTCSS FREQUENCY SCAN 22
- USING DCS 22
- SIGNALING-3 23
- DCS CODE SCAN 23
- USING CROSS TONE 23
- MANUAL DIALING 24
- AUTOMATIC DIALER 24
- DTMF KEY LOCK 25
- EchoLink 26
- Green: To line out terminal 27
- OTHER OPERATIONS 28
- OTHER OP-2 29
- PROGRAMMABLE VFO 29
- ■ Squelch Hang-up Time 30
- ■ Mute Hang-up Time 30
- OTHER OP-4 31
- TIME-OUT TIMER (TOT) 31
- MICROPHONE SENSITIVITY 31
- POWER ON MESSAGE 31
- DISPLAY ILLUMINATION 31
- OTHER OP-5 32
- PROGRAMMABLE FUNCTION KEYS 32
- KEY LOCK 32
- OTHER OP-6 33
- AUTOMATIC POWER OFF (APO) 33
- PC PORT SPEED 33
- DISPLAY PARTITION BAR 33
- POWER ON PASSWORD 33
- WHAT IS GPS? 34
- GPS AND APRS POSITION FORMAT 34
- INTERNAL GPS FUNCTION ON/OFF 35
- GPS DATA SETUP (1) 35
- GPS DATA SETUP (2) 35
- TRACK LOG 36
- LOG SETUP 36
- TARGET POINT 37
- MARK WAYPOINT 37
- ■ Mark Waypoint List 38
- ■ Deletes all Mark Waypoints 38
- PACKET-1 39
- PACKET MODE 39
- PACKET-2 40
- DATA BAND 40
- COM PORT SPEED 40
- USING EXTERNAL TNC 40
- PACKET-3 41
- TNC COMMANDS LIST 41
- PACKET-4 42
- PACKET-5 43
- PACKET-6 44
- PACKET-7 45
- DIGIPEAT 46
- ADJUSTING THE INTERNAL CLOCK 47
- WEATHER STATION 47
- RECEIVING APRS DATA 48
- ACCESSING RECEIVED APRS DATA 48
- CURSOR CONTROL 49
- DISPLAY EXAMPLE 49
- SORT FUNCTION 50
- DISPLAY FILTER FUNCTION 51
- RECEIVING A MESSAGE 51
- ENTERING A MESSAGE 52
- TRANSMITTING A MESSAGE 53
- BASIC SETTINGS 53
- SETTING GPS PORT 54
- SETTING INTERNAL TNC 54
- SETTING WAY POINT 55
- COM PORT ON/OFF 55
- PROGRAMMING POSITION DATA 55
- SETTING BEACON INFORMATION 55
- SELECTING A POSITION COMMENT 56
- STORING STATUS TEXT 56
- QSY FUNCTION 56
- SETTING PACKET FILTER 57
- SELECTING YOUR STATION ICON 57
- SETTING BEACON TX ALGORITHM 58
- PROGRAMMING A PACKET PATH 59
- VOICE ALERT 60
- WEATHER STATION DATA OUTPUT 61
- SETTING AS A DIGIPEATER 61
- STORING USER PHRASES 62
- STORING AUTO MESSAGE REPLY 63
- SETTING SOUND 64
- SETTING INTERRUPT DISPLAY 64
- You can enter 0 to 9, A to Z 65
- PACKET MONITOR DISPLAY 66
- DX PACKETCLUSTERS MONITOR 67
- TRANSCEIVER RESET 68
- VGS-1 (OPTIONAL) OPERATION 69
- VOICE RECORDER 70
- ■ Continuous Recording 71
- ■ Playback 71
- ■ Playback Repeat 71
- ■ Playback Repeat Interval 71
- REPEATER OPERATION MODE 72
- REPEATER TX HOLD 72
- REPEATER ID TX 72
- CROSS BAND REP-1 72
- PREPARATION 73
- CONTROL OPERATION 73
- WIRELESS OP-1 73
- WEATHER ALERT ON/ OFF 74
- WEATHER ALERT SCAN 74
- SKY COMMAND SYSTEM II 75
- SKY CMD-2 76
- PREPARATION FLOW 76
- SKY CMD-3 77
- PROGRAMMING CALLSIGNS 77
- PROGRAMMING A TONE FREQUENCY 77
Related products and manuals for Radio Kenwood TM-D710GA
Radio Kenwood KDC-X498 User Manual
(50 pages)
(50 pages)
Radio Kenwood TS-590S User Manual
(92 pages)
(92 pages)
Radio Kenwood CAW1170-09 User Manual
(4 pages)
(4 pages)
Radio Kenwood CAW1201-05 User Manual
(3 pages)
(3 pages)
Radio Kenwood CAW1179-07 User Manual
(2 pages)
(2 pages)
Radio Kenwood CAW1035-01 User Manual
(14 pages)
(14 pages)
Radio Kenwood CAW1035-06 User Manual
(7 pages)
(7 pages)
Radio Kenwood CAW2130-05 User Manual
(2 pages)
(2 pages)
Radio Kenwood CAW-TY2290 User Manual
(3 pages)
(3 pages)
Radio Kenwood CAW1213-02 User Manual
(2 pages)
(2 pages)
Radio Kenwood CAW-MZ2032 User Manual
(3 pages)
(3 pages)
Radio Kenwood CAW1130-06 User Manual
(4 pages)
(4 pages)
Radio Kenwood TK-290/390 User Manual
(24 pages)
(24 pages)
Radio Kenwood CAW2088-01 User Manual
(1 pages)
(1 pages)
Radio Kenwood CAW1040-11 User Manual
(2 pages)
(2 pages)
Radio Kenwood TS-2000E User Manual
(4 pages)
(4 pages)
Radio Kenwood SPECTRUM 870AV User Manual
(4 pages)
(4 pages)
Radio Kenwood CAW1179-16 User Manual
(2 pages)
(2 pages)
Radio Kenwood CAW-OP7800 User Manual
(4 pages)
(4 pages)
Radio Kenwood CAW1200-01 User Manual
(2 pages)
(2 pages)
Brother 4000D podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Maszyny do szycia Brother 4000D.
Dostarczamy 3 pdf podręczników Brother 4000D do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika, Przewodnik Instalacji
Comments to this Manuals