Kenwood TS-480SAT User Manual Page 79
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
71
13 OPERATOR CONVENIENCES
■ Voice Guide Announcement Volume
Turning the AF control does not change the volume
for the Voice Guide announcement volume. To
change the announcement volume , access Menu
No. 15 to select the volume level from “1” to “7” or
“oFF”.
■ Voice Guide Announcement Speed
If you feel the Voice Announcement speed is too slow
or fast, you can adjust the Voice Announcement
speed. Five different speed can be configured.
Access Menu No. 16 and select “0” to “4”. 0 is the
slowest speed and 4 is the fastest speed. The default
speed is 1.
CROSSBAND REPTEATER
If you have a TM-D700 transceiver and another VHF
or UHF transceiver, you can set up the TS-480
transceiver and TM-D700 transceiver as a crossband
repeater. The TM-D700 will receive signals you
transmit from the additional VHF or UHF transceiver
when both transceivers are set with the same
frequency. The signal is then routed to the TS-480
transceiver and retransmitted on the frequency you
have set upon the TS-480 transceiver. Likewise,
signals received on the TS-480 transceiver are routed
to the TM-D700 and retransmitted to the transceiver
you have with you, allowing you to hear the received
call in a distant location.
To interface between the TS-480 transceiver and
TM-D700 transceiver, refer to “CROSSBAND
REPEATER” for details {page 79}.
You need a cable that has mini-DIN (6-pin) male
connector at both ends.
Note:
For the repeater function to operate, the squelch levels of both
transceivers (TS-480 and TM-D700) must be adjusted properly so
that no background noise can be heard. Because the transmission is
controlled by monitoring the squelch status only.
Operation
The crossband repeater function uses 2 frequency
bands to receive and transmit signals. When a signal
is received on one band, it is retransmitted on the
other band.
1 Select a desired transmission/ reception VHF or
UHF frequency on the TM-D700 transceiver.
2 Confirm PTT icon is visible on the crossband
repeater frequency on the TM-D700 transceiver.
3 Select the same frequency for the terminal
transceiver.
4 Select a desired HF/ 50 MHz frequency on the
TS-480 transceiver.
5 Adjust the squelch threshold level so that both
TS-480 transceiver and TM-D700 transceiver
mute.
6 Press [MENU/ F. LOCK] on the TS-480, then turn
MULTI control to access Menu No. 57.
7 Press [ ] to select “on”.
• When the TS-480 transceiver’s squelch opens,
the TM-D700 transceiver retransmits the
incoming audio signal on the VHF or UHF
frequency at the same time.
•When the TM-D700 transceiver’s squelch
opens, the TS-480 transceiver retransmits the
incoming audio signal on the HF/ 50 MHz
frequency.
8 Access Menu Nos. 46 and 47 and press [ ]/ [ ]
to adjust the input/ output audio level.
9 To quit the TM-D700 repeater operation,
disconnect the interface cable between
transceivers and access Menu No. 57 on the
TS-480 transceiver and select “oFF”.
- TS-480HX 1
- TS-480SAT 1
- FCC WARNING 2
- BY THE FCC 2
- THANK YOU 3
- PRECAUTIONS 5
- CONTENTS 6
- INSTALLATION 9
- 1 INSTALLATION 10
- ANTENNA CONNECTION 10
- GROUND CONNECTION 10
- IGNITION NOISE 10
- DC POWER CABLE CONNECTION 10
- )renutannetnalanretxenaroF( 13
- TX/ RX UNIT 15
- REMOTE CONTROL PANEL 15
- YOUR FIRST QSO 16
- 2 YOUR FIRST QSO 17
- TRANSMISSION 17
- GETTING ACQUAINTED 18
- 3 GETTING ACQUAINTED 19
- LCD DISPLAY 21
- REMOTE CONTROL PANEL (REAR) 25
- MICROPHONE 25
- OPERATING BASICS 26
- 4 OPERATING BASICS 27
- SELECTING A BAND 27
- SELECTING A MODE 27
- ADJUSTING SQUELCH 27
- SELECTING A FREQUENCY 27
- SELECTING TRANSMISSION POWER 28
- MICROPHONE GAIN 29
- MENU SETUP 30
- 5 MENU SETUP 31
- MENU CONFIGURATION 31
- )1ECIOV( 33
- )INOMXR( 33
- ALPHABETICAL FUNCTION LIST 34
- BASIC COMMUNICATIONS 35
- 6 BASIC COMMUNICATIONS 36
- AUTO ZERO-BEAT 37
- ENHANCED COMMUNICATIONS 38
- 7 ENHANCED COMMUNICATIONS 39
- TRANSMITTING A TONE 40
- TONE FREQ. ID SCAN 40
- CTCSS FREQ. ID SCAN 41
- COMMUNICATING AIDS 42
- 8 COMMUNICATING AIDS 43
- AGC (AUTOMATIC GAIN CONTROL) 43
- VOX (VOICE-OPERATED TRANSMIT) 44
- SPEECH PROCESSOR 45
- TX Filter Bandwidth (SSB/ AM) 46
- TX Equalizer (SSB/ FM/ AM) 46
- Frequency Response Curves 46
- CHANGING KEYING SPEED 47
- AUTO WEIGHTING 47
- BUG KEY FUNCTION 48
- CW MESSAGE MEMORY 48
- FREQUENCY CORRECTION FOR CW 49
- AUTO CW TX IN SSB MODE 49
- MIC UP/ DWN KEY PADDLE MODE 49
- SPECIALIZED COMMUNICATIONS 50
- 9 SPECIALIZED COMMUNICATIONS 51
- SLOW SCAN TV/ FACSIMILE 52
- REJECTING INTERFERENCE 53
- 10 REJECTING INTERFERENCE 54
- BEAT CANCEL (SSB/ FM/ AM) 55
- NOISE REDUCTION (ALL MODES) 55
- PRE-AMPLIFIER 57
- ATTENUATOR 57
- CW REVERSE (RECEPTION) 57
- MEMORY FEATURES 58
- 11 MEMORY FEATURES 59
- MEMORY RECALL AND SCROLL 59
- MEMORY TRANSFER 60
- STORING FREQUENCY RANGES 61
- MEMORY CHANNEL LOCKOUT 62
- ERASING MEMORY CHANNELS 62
- MEMORY CHANNEL NAME 62
- STORING INTO QUICK MEMORY 63
- TEMPORARY FREQUENCY CHANGES 63
- QUICK MEMORY ➡ VFO TRANSFER 63
- VFO SCAN 64
- PROGRAM SCAN 64
- 12 SCAN 65
- PROGRAM SCAN PARTIALLY SLOWED 65
- SCAN HOLD 65
- SCAN RESUME METHOD 66
- ALL-CHANNEL SCAN 66
- GROUP SCAN 67
- OPERATOR CONVENIENCES 68
- 13 OPERATOR CONVENIENCES 69
- BEEP FUNCTION 70
- BRIGHTNESS 71
- KEY ILLUMINATION 71
- FREQUENCY LOCK FUNCTION 71
- TUNING CONTROL LOCK FUNCTION 71
- EQUALIZING RECEIVING AUDIO 72
- SETTING UP 74
- USING QUICK TRANSFER 74
- COMMUNICATION PARAMETERS 75
- RECORDING MESSAGES 76
- MESSAGE PLAYBACK 77
- CONSTANT RECORDING 77
- VOICE GUIDE 78
- CROSSBAND REPTEATER 79
- DX PACKETCLUSTER TUNE 80
- SKY COMMAND II (K-TYPE ONLY) 81
- SKY COMMAND II DIAGRAM 81
- PREPARATION 81
- CONTROL OPERATION 81
- USING TH-D7A AS A COMMANDER 82
- To COM port 84
- Straight-wired 84
- Linear Amp 85
- Use the supplied 85
- TS-480HX/ SAT 85
- MCP/ TNC 86
- DATA connector 86
- (Front view) 86
- ANT 1 connector 86
- TS-480 transceiver 87
- TM-D700 transceiver 87
- Cross-wired cable 87
- INSTALLING OPTIONS 89
- 15 INSTALLING OPTIONS 90
- TROUBLESHOOTING 91
- 16 TROUBLESHOOTING 92
- INITIAL SETTINGS 96
- PARTIAL RESET 96
- FULL RESET 96
- OPTIONAL ACCESSORIES 98
- SPECIFICATIONS 99
- 20 SPECIFICATIONS 100
- 19 INDEX 102
Related products and manuals for Boating Accessories Kenwood TS-480SAT
(104 pages)
Boating Accessories Kenwood TS-480HX User Manual
(104 pages)
(104 pages)
Boating Accessories Kenwood TM-451A User Manual
(130 pages)
(130 pages)
© 2020, manymanuals.com. All rights reserved. | 0.634 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals