Kenwood K-501USB User Manual download pdf (Page 22)

English

How to Use This Volume “Operating Procedures”

32 33

Recording Music from Kenwood Digital Audio

Player

Record

Select the D.AUDIO source.

Prepare recording

Recording Music from Kenwood Digital Audio Player

Pre pa ra tions

Connect a Kenwood digital audio player

to the D.

AUDIO IN connector. (Refer to

page 10 of "Read Before Use".)

Make sure that the memory card is in

stop mode.

If is lit

press the

RANDOM key to cancel the

random play mode.

Memory card only

To stop recording

Enter record-pause mode.

Select the music ﬁ le to be recorded.

Let playback pause

temporarily.

Start recording.

Press the M E M O RY

REC key again to enter

record mode.

If the memory card contains a folder named AL_Z90

or higher, a message [CHECK REFRESH] is displayed

and recording cannot be started. In this case, it

is required to

rearrange the folders by means of

refreshing. (See page 52.)

To let recording pause

temporarily

* When the dedicated cable is used, the Kenwood digital

audio player can be controlled from the main unit or

remote control unit

Playback pauses at the beginning of the selected music  le.

* If the dedicated cable is not used for the connection,

prepare recording on the connected Kenwood digital

audio player.

Dividing music during recording

During recording from the TUNER,

AUX or D.AUDIO source to a memory

card, the recorded music file can be

divided into multiple music files by

manually entering a track mark (music

division mark). Each press of the key

or knob creates a new music  le from

that point.

Press at the point you

want to divide the music

* The track marks can

also b e enter e d

automatically. (See

page 59.)

* To

resume recording, press the

same key again. Note that a new

music

 le is created at this time.

* Do not connect a USB audio player during

recording, as this will stop the recording.

* To

change the record mode setup,

see pages 56 to 61.

A message [STOP REC No Capacity]

is displayed. Erase the unnecessar

music

ﬁ les before retrying recording

from the beginning. (See page 36.)

Do not switch the system OFF or apply shock or

vibration to it while [DATA WRITING] is displayed.

The memory card stops and a message

[DATA WRITING] is displayed.

If the power to the system is shut o before [DATA

WRITING] disappears, the recorded data will be lost.

When the memory card becomes

full before completion of recording:

When recording completes:

* A message [Don't remove

MEMORY CARD] is scrolled

* If the dedicated cable is not used

for the

connection, start playback on the connected

Kenwood digital audio player.

If the audio recorded is distorted

or too lo

Adjust the recording level. (See page 58.)

The memory card is put

to record-pause mode.

Start playback of the Kenwood

digital audio player.

* A message [Don't remove

MEMORY CARD] is scrolled

Hint

* Correc t operation may not

be possible without correct

preparations.

USB audio player

connected to the

USB connector

The section “Preparations” does not

mention how to load a CD, insert

a memory card or connect the

system components. For details,

refer to "Connections" on page 8

or "Basic Operation" on page 24.

Certain pages show the specific

preparation procedures in place of

the illustration below showing the

remote control unit and main unit.

Operation-target audio sources

Keys for use in operation from

the main unit

Keys for use in operation from

the remote control unit

Preparations before operation

Radio

Memory card

inserted in the

main unit

Auxiliary component

connected to the AUX

IN connector

Kenwood digital audio

player connected to the

D.AUDIO IN connector

* Certain pages do not show

this illustration.

* Certain pages do not show

this illustration.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 28

Comments to this Manuals

No comments

Kenwood K-501USB User Manual Page 22

Comments to this Manuals

Related products and manuals for Acoustics Kenwood K-501USB