Kenwood KRF-V4550D User Manual download pdf (Page 17)

Operations

Jot down the distance to each of the speakers.

Distance to front speakers: ____ feet (meters)

Distance to center speaker: ____ feet (meters)

Distance to surround speakers: ____ feet (meters)

2 Use the MULTI CONTROL to select the distance to the front

speakers.

Input level adjustment (analog sources only)

If the input level of an analog source signal is too high, adjust the input

level.

1 Use the INPUT SELECTOR knob to select the source who’s

input level you want to adjust.

• You can store a separate input level for each input source. If the

MONITOR function is on, you can store an input level for when

MONITOR is on independently of the input levels for the input

sources.

2 Press the SOUND key several times until the "INPUT" indica-

tion appears.

3 Use the MULTI CONTROL to adjust the input level.

• The adjustment mode is displayed for approximately eight sec-

onds.

• The input level may be adjusted to any one of three settings: 0,

-3, and -6. (The initial setting is 0.)

4 Press the SOUND key to return to the input indication.

Preparing for playback

Normal playback

Some preparatory steps are needed before starting playback.

Turning on the receiver

1 Turn on the power to the related components.

2 Turn on the power to this receiver by pressing POWER and ON/

STANDBY keys.

Selecting MD/TAPE

Select the source name corresponding to the component connected to

the MD/TAPE jacks. The initial factory setting is "TAPE". To change the

source name associated with the MD/TAPE jacks to "MD," follow the

steps below:

1 Use the INPUT SELECTOR knob to select "TAPE".

2 Hold down the AUTO key for more than 2 seconds.

• The source indication changes to "MD".

• To return to the original indication, repeat the above procedure.

• You also will need to change the name input to the remote control

to "MD".

Selecting the input mode

If you have selected a component connected to the CD/DVD, DVD/

6ch or VIDEO2/MONITOR jacks, make sure that the input mode

setting is correct for the type of audio signal to be used. 7

5 Setup is complete when the input indication reappears.

Display when all speakers have been selected.

• The speakers you selected appear on the display. Confirm that all

the speakers have been correctly selected.

The speaker indicator to be adjusted blinks.

Indication in feet Indication in meters

1 Measure the distance from the listening position to each of the

speakers.

• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),

adjustable in 1 foot (0.3 m) increments.

3 Press the SET UP key.

4 Repeat steps 2 and 3 to input the distance for each of the

speakers.

LFE

SRSLS

TI.VOLB

CLIP MUTE

RDS EON PTY

TP TA NEWS

STEREO

MHz

kHz

PRO LOGIC

DOWN MIX

DIGITAL

S.DIRECT

MONITOR

DSP

MEMO

ST.

TUNED

AUTO SOUND

AUTO

LFE

SRSLS

TI.VOLB

CLIP MUTE

RDS EON PTY

TP TA NEWS

STEREO

MHz

kHz

PRO LOGIC

DOWN MIX

DIGITAL

S.DIRECT

MONITOR

DSP

MEMO

ST.

TUNED

AUTO SOUND

AUTO

LFE

SRSLS

TI.VOLB

CLIP MUTE

RDS EON PTY

TP TA NEWS

STEREO

AUTO

INPUT MODE

POWER

ON/STANDBY

INPUT SELECTOR

SPEAKER

MUTE

LFE

SRSLS

TI.VOL

CLIP MUTE

RDS EON PTY

TP TA NEWS

SP A

The speaker indicator lights.

Press the SPEAKER key to switch the speakers on and off.

Preparing for surround sound

Input the distance to the speakers.

*4967/01-/EN 3/19/01, 6:34 PM17

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 31 32

Comments to this Manuals

No comments

Kenwood KRF-V4550D User Manual Page 17

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Kenwood KRF-V4550D