Kenwood TS-590S User Manual

TS-590S KENWOOD NETWORK COMMAND SYSTEM Setting Manual© October/15/2010

10Router Same as host station. Modem Same as host station. LAN environment Firewall Same as host station. Provider Same as host station.

114. Settings 4.1. Connecting Communications Cables Connect the host station PC and TS-590S using an RS-232C or USB cable. Note: RS-232C cable

12Connect sound functions and audio cables with reference to the following diagram. Fig. 4.2.2: Connecting audio cables Reference: If the TS-59

134.3. Transceiver Settings Make the settings required to implement KNS operations using transceivers. ● Set the audio path settings With KNS

14● Audio I/O level settings Use the following menu to adjust audio transmission input levels from the PC, and receive audio output levels to the PC

15Note: Select from 3/ 5/ 10/ 20/ 30(minutes) excepting OFF, depending on the situation to use. ● Prohibit transmission setting If using the host

164.4. Setting Transmission Methods for Audio Input to the Rear Terminal The [SEND] keys on the PTT of the microphone connected to the TS-590S, an

174.5. Setting Broadband Routers If implementing KNS operations via the internet, it is necessary to set the broadband router connected to the host

184.6. Software Installation and Settings Install the software required for KNS operations on the host station PC and the remote station PC, then pe

194.7. Windows Firewall Settings With the host station PC, receiving connections from networks and the internet using the ARHP-590 are blocked by th

2CONTENTS 1. Relevant Models ...3 2. Objecti

205. Limitations Caution! 5.1. PC Environment Limitations Check that the ARCP-590 and ARHP-590 operations use Windows XP SP3 or later, Windows Vi

215.3. Program Limitations CW operations are possible, but keying using normal e-keys is not possible. Strings entered using the keyboard are coll

226. Frequently Asked Questions This section introduces questions that have been asked to date, and subjects verified by Kenwood Corporation. Q

23 Question Answer Installation I want to use headsets, USB headsets, and Bluetooth headsets on the remote station PC. Will there be any problems

24 Question Answer Why can't I use the ARCP-480? The ARCP-480 is for the TS-480 only. Use the ARCP-590 with the TS-590S. Why can't I

25 Question Answer If using the sound functions in comprehensive chipsets, try an independent sound card or USB sound. Adjust the ACC2 audio leve

26 Question Answer Refer to the VoIP software user manual, and check the settings. Check that an existing device has been specified for the PC

27 Question Answer Comprehensive security software, etc. I'm using comprehensive security software, but when I try a KNS connection, the wa

28(Supplement): FAQ: Explaining the Internet "Cannot operate transceiver" Fig. 1 As shown in Fig. 1, even though only one broadband rout

31. Relevant Models This user guide is for the TS-590S. Using the TS-590S and KENWOOD NETWORK COMMAND SYSTEM (hereinafter called "KNS")

43. Outline 3.1. Overall Configuration Fig. 3.1.1: Example of internal LAN configuration (In this diagram, the modem, router, and hub have bee

5 Fig. 3.1.2: Example of KNS configuration via the internet The host station and remote station can be installed in any location with an internet

63.3. Host Station (Transmitter) Configuration Transceiver TS-590S The TS-590S transceiver is supported. The ARCP-590 and ARHP-590 are speciali

7Run-time To use KNS on Windows XP, Microsoft .NET Framework 2.0 or later is required. If it is not installed, install it when installing ARHP-590.

83.4. Overview of Remote Station (Operator) Operations The remote station is configured using a PC connected to the network, and a microphone and sp

93.5. Remote Station (Operator) Configuration PCサウンド機能ARCP-590VoIPソフトウェア送信音声受信音声LAN/WAN Connection Audio To exchange audio transmissions, con