INSTRUCTION MANUALVHF FM TRANSCEIVER (TK-2100)ProTalk™ VHFUHF FM TRANSCEIVER (TK-3100)ProTalk™ UHFKENWOOD CORPORATION©B62-0950-30 (K)09 08 07 06 05 04
Installing the AntennaScrew the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise u
Installing the Cover over the Speaker/ Microphone JacksIf you are not using a speaker/ microphone, install the cover over the speaker/ microphone jack
GEniNG ACQUAINTEDSpeaker/microphonejacksPress this switch, then speak into the microphone to call a station. Release the switch to receive.d)
OPERATING BASICS1 Switch ON the transceiver by turning the Power switch/ Volume control clockwise.• A beep sounds.2 Adjust the volume by pressing an
CHANNEL FREQUENCY SELECTIONYou can change the frequency on each channel.The transceiver will exit the setup mode if no operationis performed within 5
ProTalk^M VHP:ActionFrequencyBeeppatternNo.Value (MHz)ColorPress PTT 1 time1151.6250 Red•Press PTT 2 times2151.9550Purple• •Press PTT 3 times3154.5700
6 Press the Monitor key to complete the setting.• The red LED blinks twice.7 Press the Monitor key again to confirm the beep pattern of th
QUIET TALK (QT)QT allows you to hear only signals on your channel which are coded to match your transceiver. When a received signal has a code differe
QT Tone SetupNote:♦ Refer to the signalling codes listed in the table on page 11.♦ When selecting a single digit number (0 ~ 9). always use 2 digits
4 Press the PTT switch to select the 10’s digit of the signalling number• Each time you press the PTT switch, a beep sounds and the 10's digit o
INTRODUCTIONKENWOOD welcomes you to the Business Radio Service (BRS). Your KENWOOD 2-way Business Radio is called a 'Iransceiveh’, meaning ‘Irans
---------------------------------------------------------------^---------------Action I ValueBeep patternPress and hold PTT for 2 seconds j x 01 secon
9 Press the Monitor key again to confirm the beep pattern of the selected signalling number.10 On the 2 channel modeL repeat steps 3 to 9
CHANNEL SETTING CONFIRMATIONYou can confirm the channel settings of your transceiverNote: Añer confirming a setting, you must turn the power OFF and t
Confirmation Beep PatternsNumberBeep patternNumber Beep pattern01 second tone5• • • • •1•6— •2• •7— • •3• • •8 ; -•••4•«• •9~ •Reference TablesFactory
TRANSCEIVER FUNCTIONSTime-out Timer (TOT)The purpose of the Time-out Timer is to prevent any single person from using a channel for an extended period
CHARGING THE NiCd BAHERY PACKInitially charging the battery pack after purchase or extended storage (greater than 2 months) will not bring the battery
1 Plug the AC adaptor cable into the adaptor jack located on the rear of the charger.2 Plug the AC adaptor into an AC outlet.3 Slide the NiCd batte
OPTIONAL ACCESSORIESYou can use the following accessories with your transceiver;• KNB-14; Standard Battery (7.2 V/ 600 mAh)• KNB-15A: Long Life Bat
TROUBLESHOOTING GUIDEProblem I SolutionNo power.: • The battery pack may be dead. Recharge or replace the battery pack.• The battery pack may not be i
FCC LICENSE INFORMATIONYour KENWOOD radio operates on communications frequencies which are subject to FCC (Federal Communications Commission) Rules &a
MODELS COVERED BY THIS MANUALProTalk^*^ VHF(TK-2100):1 channel VHF FM Transceiver/2 channel VHF FM TransceiverProTalk^'^ UHF (TK-3100):1 channel
One or more of the following statements may be applicable:FCC WARNINGThis equipment generates or uses radio frequency energy. Changes or modifications
CONTENTSUNPACKING AND CHECKING EQUIPMENT...Supplied Accessories...PREPARATION...
UNPACKING AND CHECKING EQUIPMENTwCarefully unpack the transceiver. We recommend that you identify the items listed in the following table before disca
Antenna(ProTalk™ VHP) (ProTalk’^ UHF)AC adaptor NiCd battery Speaker/ microphonepack (KNB-14) jack coverSpeaker/ microphone locking bracketf‘<33S
PREPARATION Installing/ Removing the NiCd Battery PackThe battery pack is not charged at the factory;charge it before use {page 19}.Average battery p
Comments to this Manuals