Kenwood TS-2000 User Manual download pdf (Page 74)

SCAN

Scan is a useful function for hands-off monitoring of

your favorite frequencies. By becoming comfortable

with all types of Scan, you will increase your operating

efficiency.

This transceiver provides the following types of scans.

epyTnacS esopruP

lamroN

nacS

nacSOFV

ehtfodnaberitneehtsnacS

detcelesuoyycneuqerf

margorP

nacS

ycneuqerfcificepsehtsnacS

yromeMniderotssegnar

992~092slennahc

nacSzHM

nihtiwseicneuqerfehtsnacS

egnarzHM1a

yromeM

nacS

lennahC-llA

nacS

,slennahcyromeMllasnacS

992ot00morf

nacSpuorG

yromeMcificepsehtsnacS

spuorglennahc

llaC

nacS

OFV

dnalennahcllaCehtsnacS

ycneuqerfOFVtnerruceht

yromeM

lennahC

dnalennahcllaCehtsnacS

lennahcyromeMdetceleseht

lausiV

*nacS

OFV

gnitarepotnerrucehtsnacS

asallewsaycneuqerf

forebmundeificeps

wolebdnaevobaseicneuqerf

langisehT.ycneuqerftaht

silennahchcaefohtgnerts

hparg-rabanideyalpsid

yromeM

lennahC

slennahcyromeMehtsnacS

langisehtsyalpsiddna

anilennahchcaefohtgnerts

hparg-rab

* Visual Scan graphically shows how frequencies in a specific range

are busy.

Note:

◆

While using CTCSS or DCS, Scan stops only for the signals that

contain the same CTCSS tone or DCS code that you selected.

◆

When using S-meter Squelch, Scan stops when the received

signal strength matches or exceeds the S-meter setting. Scan

resumes 2 seconds after the signal level drops below the S-meter

setting.

◆

Pressing and holding Mic [PTT] causes Scan to stop if it is

functioning on a non TX band. Pressing Mic [PTT] on the

scanning band causes Scan to stop.

◆

Starting Scan switches OFF the Automatic Simplex Checker.

NORMAL SCAN

When you are operating the transceiver in VFO mode,

2 types of scanning are available.

• VFO Scan

The transceiver scans the entire band of the

frequency you selected. For example, if you are

operating and receiving on the main transceiver’s

VFO A at 14.195.00 MHz, it scans all the

frequencies in the range of 30.00 kHz to

60.00000 MHz. (Refer to VFO frequency range

in the Specifications.)

• Program Scan

By programming the start and end frequency in

Memory channels 290 ~ 299 {page 62}, you can

limit the scanning frequency range. Since there

are 10 memory channels (290 ~ 299) available for

specifying the start and end frequency, you can

select one or more (a maximum of 10) ranges to

scan. This is useful when you are waiting for a DX

station on a certain frequency but the station may

appear on slightly higher or lower frequency.

VFO SCAN

VFO Scan scans the entire frequency range that is

available for the current VFO. When the Program

Scan frequency range is not programmed or no Scan

Group is selected for the Program Scan, the

transceiver also scans the entire frequency range

available for the current VFO.

If one or more Program Scan frequency ranges are

programmed in memory channels 290 to 299:

1 Press [FUNC], [SCAN/ SG.SEL].

2 If one or more memory channels are selected for

the Program Scan, the selected channels are

displayed in a larger font on the main dot-matrix

display.

In this case, press [•/ DCS/SEL] to temporarily

deselect all the channels. When there are no Scan

Group channels selected, “VFO SCN MODE”

appears on the sub dot-matrix display.

3 Press [SCAN/ SG.SEL] to return to the current

VFO mode.

4 Press [SCAN/ SG.SEL] to start the VFO Scan.

Note:

◆

While scanning, you can change the scan speed by turning the

RIT/ SUB control. Turn the control clockwise/ counterclockwise

to decrease/ increase the scan speed. The speed indicator

appears on the main dot-matrix display, where P1 is the fastest

speed and P9 is the slowest.

◆

You cannot change the VFO Scan speed in FM mode.

◆

You cannot change the VFO Scan speed on the sub-receiver.

1 2 ... 69 70 71 72 73 74 75 76 77 78 79 ... 149 150

Comments to this Manuals

No comments

Kenwood TS-2000 User Manual Page 74

Comments to this Manuals

Related products and manuals for Radio Kenwood TS-2000